manualshive.com logo in svg

Festo CMMS-ST-*-G2 Series, Сборка и инструкция по установке

Поделиться
Скачать
Festo CMMS-ST-*-G2 Series Скачать руководство пользователя страница 47

 

3. Product description 

Festo.P.BE-CMMS-ST-G2-HW-EN 1008NH 

 

47 

1

  Position 

setpoint time slot 
pattern 

2

  Position control 

cycle time 

3

  Interpolated 

position sequence 

4

  Travelled 

position sequence 
 
 

 

 

 

 

 

 

Fig. 

 

3.2 Interpolated position mode 

3.4.3

 

PROFIBUS 

The controller is connected to the PROFIBUS with a corresponding expansion module 
(CAMC-PB), which can be plugged into the expansion slot X7. If the module is plugged in, 
it automatically becomes active the next time the controller is switched on. 
The slave address is configured over the DIP switches on the front side of the controller. 
Baud rates up to 12MBaud are supported.  
FHPP with the above-described control and operating modes is used as communication 
protocol. 

3.4.4

 

DeviceNet 

The controller is connected to the DeviceNet network with a corresponding expansion 
module (CAMC-PB), which can be plugged into the expansion slot X7. If the module is 
plugged in, it automatically becomes active the next time the controller is switched on. 
The MAC-ID and baud rate are configured over the DIP switches on the front side of the 
controller. 
Baud rates up to 500 kBaud are supported.  
FHPP with the above-described control and operating modes is used as communication 
protocol. 

1

2

3 

4

Содержание CMMS-ST-*-G2 Series









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды