manualshive.com logo in svg

Festo CMMP-AS-***-M0 Series, Руководство пользователя

Поделиться
Скачать
Festo CMMP-AS-***-M0 Series Скачать руководство пользователя страница 69

4

EtherCAT interface

Festo – GDCP-CMMP-M3/-M0-C-CO-EN – 1510b – English

69

4.12

XML Device Description File

In order to connect EtherCAT slave devices simply to an EtherCAT master, there must be a description

file for every EtherCAT slave device. This description file is comparable to the EDS files for the CANopen

fieldbus system or the GSD files for Profibus. In contrast to the latter, the EtherCAT description file is in

the XML format, as is often used for internet and web applications, and contains information on the

following features of the EtherCAT slave devices:

–

Information on the device manufacturer

–

Name, type and version number of the device

–

Type and version number of the protocol to be used for this device (e.g. CANopen over Ethernet, ...)

–

Parametrisation of the device and configuration of the process data

This file contains the complete parametrisation of the slave, including the parametrisation of the Sync

Manager and the PDOs. For this reason, the configuration of the slave can be changed using this file.

Festo has created a device description file for the CMMP-AS-...-M3 motor controller. It can be down­

loaded from the Festo homepage. Its contents will now be described in more detail to permit users to

adapt this file to their application.

The available device description file supports both the CiA 402 profile and the FHPP profile via separ­

ately selectable modules.

The XML files are included on the CD-ROM supplied with the motor controller.

XML file

Description

Festo_CMMP-AS_V4p0_FHPP.xml

Motor controller CMMP-AS-...-M3 with protocol “FHPP”

Festo_CMMP-AS_V4p0_CIA402_IP7.xml

Motor controller CMMP-AS-...-M3 with protocol “CiA 402”

Tab. 4.15

XML file

You will find the most current version under 

 www.festo.com/sp

4.12.1

Fundamental structure of the device description file

The EtherCAT device description file is in the XML format. This format has the advantage that it can be

read and edited in a standard text editor. An XML file always describes a tree structure. It defines the

individual branches via nodes. These nodes have a start and end marking. Each node can contain any

number of sub-nodes.

EXAMPLE: Rough explanation of the fundamental structure of an XML file:

Содержание CMMP-AS-***-M0 Series







































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды