manualshive.com logo in svg

Festo CMMP-AS-***-M0 Series, Руководство пользователя

Поделиться
Скачать
Festo CMMP-AS-***-M0 Series Скачать руководство пользователя страница 190

7

Operating modes

190

Festo – GDCP-CMMP-M3/-M0-C-CO-EN – 1510b – English

Object 6086

h

: motion_profile_type

The object motion_profile_type is used to select the type of positioning profile.

Index

6086

h

Name

motion_profile_type

Object Code

VAR

Data Type

INT16

Access

rw

PDO mapping

yes

Units

–

Value Range

0, 2

Default Value

0

Value

Curve form

0

Linear ramp

2

Jerk-free ramp

7.3.3

Description of function

There are two possibilities for passing on a target position to the motor controller:

Simple positioning task

If the motor controller has reached a target position, it signals this to the host with the bit tar­

get_reached (bit 10 in the object statusword). In this operating mode, the motor controller stops when

it has reached the goal.

Sequence of positioning tasks

After the motor controller has reached a target, it immediately begins travelling to the next target. This

transition can occur smoothly, without the motor controller meanwhile coming to a standstill.

These two methods are controlled through the bits new_set_point and change_set_immediately in the

object controlword and set_point_acknowledge in the object statusword. These bits are in a question-

answer relationship to each other. This makes it possible to prepare a positioning task while another is

still running.

Содержание CMMP-AS-***-M0 Series







































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды