Festo 548076 Скачать руководство пользователя

Страница: 84 / 92

84 / 92

Festo 7DHTGd_en

4.5.7

Installing the plate

1. Push the rail of the guide segments from underneath onto the clamping

ring.

The plate seal is supplied in different lengths depending on the size. Before

being installed it must be shortened to the correct length (see table) and the
cut surfaces must be glued together using superglue.

Type

Length of plate seal

DHTG-65-…-A

230

+-1

DHTG-90-…-A

320

+-1

DHTG-140-…-A

478

+-1

DHTG-220-…-A

729

+-1

Note

The sealing lip of the plate seal must face the underside of the clamping ring.

2. Press the new plate seal into the slot in the edge of the clamping ring.

3. Insert both rails of the guide segments in the housing.

4.  Check the hole pattern on the plate.
5.  Insert the plate on the pinion in the housing.
6.  Turn the plate slowly, until it engages in the pinion gearing.

Содержание 548076





























































































Результаты поиска

Содержание 548076

Отзывы:

Похожие инструкции для 548076

Бренды по названию

Популярные бренды

Festo 548076, Инструкции по ремонту

Результаты поиска

Содержание 548076

Отзывы:

Похожие инструкции для 548076

Бренды по названию

Популярные бренды