Festo 548076 страница 80 Скачать руководство пользователя

Страница: 80 / 92

80 / 92

Festo 7DHTGd_en

29. Tighten the socket head screws in the impact plate with the appropriate

tightening torque (see table).

Type

Torque

Number of socket head screws

DHTG-65-…-A

2.9 Nm

DHTG-90-…-A

2.9 Nm

DHTG-140-…-A

9.9 Nm

DHTG-220-…-A

9.9 Nm

30. Tighten the hollow bolt in the impact plate with the appropriate tightening

torque (see table).

Type

Torque

DHTG-65-…-A

1.5 Nm

DHTG-90-…-A

1.5 Nm

DHTG-140-…-A

5.5 Nm

DHTG-220-…-A

5.5 Nm

4.5.4

Assembling the plate (DHTG-65 and DHTG-90)

1. Push the rail of the guide segments onto the plate.

2. Press the new O-ring into position on the inside of the hole in the plate.

Note

If there is a heavy-duty spring pin in the plate (from series F8), it is not possi-
ble to mount index plates without an additional hole.

3. Place the index plate on the centring bolts in the plate with the countersinks

for the countersunk screws facing upwards.

Содержание 548076





























































































Результаты поиска

Содержание 548076

Отзывы:

Похожие инструкции для 548076

Бренды по названию

Популярные бренды

Festo 548076, Инструкции по ремонту

Результаты поиска

Содержание 548076

Отзывы:

Похожие инструкции для 548076

Бренды по названию

Популярные бренды