Festo 548076 Скачать руководство пользователя страница 74

Страница: 74 / 92

74 / 92

Festo 7DHTGd_en

3. Drive the cover into the guide.

A plastic hammer and a sleeve with the following dimensions can be used as
assembly aids to drive the cover into the guide.

Type

Max. outside diameter of
the feed sleeve

Min. inside diameter of
the feed sleeve

DHTG-45-

-A

17 mm

10 mm

DHTG-90-

-A

24 mm

15 mm

DHTG-140-

-A

29 mm

18 mm

DHTG-220-

-A

39 mm

24 mm

Insert the new retaining rings in the guides and check for correct fit.

5. Insert the metal sheet into the slot of the bolts.

4.5.3

Installing the gear racks

1. Insert new piston seals on both gear racks so that the open side of the

piston ring faces the closed side of the gear rack.

2. Place the housing on its left side to identify the position of the gear racks.
3. Grease the gear racks with LUB-E1 before inserting them.

Содержание 548076





























































































Результаты поиска

Содержание 548076

Отзывы:

Бренды по названию

Популярные бренды

Festo 548076, Инструкции по ремонту

Результаты поиска

Содержание 548076

Отзывы:

Бренды по названию

Популярные бренды