Festo 548076 Скачать руководство пользователя

Страница: 64 / 92

64 / 92

Festo 7DHTGd_en

9. Lever the O-ring out of the inside of the hole in the plate.

10. Lever the two rails of the guide segments out of the housing.

If only plate components have to be repaired, you can continue with the assembly in

Chapter 4.5.6 on page 82

4.4.5

Removing the gear racks

The installation position of several components depends on the configuration of the rotary indexing table and can

differ from the images shown here.
The position of the gear racks, indexing pins, blanking plugs and shock absorber must always be marked for
subsequent assembly.

1. Loosen the socket head screws in the impact plate on the front of the hous-

ing (do not unscrew and remove).

2. Unscrew hollow screw in the impact plate.

Note

The impact plate is subjected to spring tensioning on one side and can tilt
when the socket head screws are unscrewed.

3. Unscrew the socket head screws in the impact plate.

Type

Number of socket head screws

DHTG-65-…-A

DHTG-90-…-A

DHTG-140-…-A

DHTG-220-…-A

Содержание 548076





























































































Результаты поиска

Содержание 548076

Отзывы:

Похожие инструкции для 548076

Бренды по названию

Популярные бренды

Festo 548076, Инструкции по ремонту

Результаты поиска

Содержание 548076

Отзывы:

Похожие инструкции для 548076

Бренды по названию

Популярные бренды