manualshive.com logo in svg

Ferris 5901756, Руководство оператора

Поделиться
Скачать
Ferris 5901756 Скачать руководство пользователя страница 11

Not for 

Reproduction

11

Features and Controls

Unit Control Functions and Locations

The information below briefly describes the function of

individual controls. Starting, stopping, and driving require

the combined use of several controls applied in specific

sequences. To learn what combination and sequence of

controls to use for various tasks see the 

Operation

 section.

4

Unit Controls List

A. Engine Throttle Control Lever
B. Choke Control Lever
C. Speedometer
D. Hour Meter
E. Ignition Switch
F. Hydraulic Oil Expansion Tank
G. Fuel Tank Cap
H. Cam Lever
I. Parking Brake Pedals
J. Operator Platform

K. Operator Cushion
L. Rear Stationary Lever 
M. Left Ground Speed Control Lever
N. Maximum Forward Speed Control Bar
O. Right Ground Speed Control Lever

Engine Throttle Control Lever

The throttle controls engine speed. Move the throttle forward

to increase engine speed and back to decrease engine

speed. 

 

FAST engine throttle speed

 

SLOW engine throttle speed

Choke Control Lever

Close the choke for cold starting. Open the choke once the

engine starts. A warm engine may not require choking. Move

the lever forward to close the choke and rearward to open the

choke.

 

CLOSED choke position

 

OPEN choke position

Speedometer

This unit is equipped with a speedometer to help you

track the ground speed of the machine so you can ensure

ground coverage while operating the unit. In addition to a

speedometer, other modes that can be accessed on the

speedometer is a clock and trip distance recording. There are

other functions built into the speedometer but they are not

used on this unit.

5

A. Left Button (DOWN)
B. Center Button (MODE)
C. Right Button (UP)
D. Speed Display
E. Clock Display
F. Trip Distance Display

Содержание 5901756









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды