Not for
Reproduction
Tracking Adjustment
1.
Park the machine on a flat, level surface such as a concrete
floor. Disengage the PTO, engage the parking brake, turn
the ignition switch to OFF, and remove the key.
2.
If the unit veers to the left, loosen the jam nut (A, Figure 48)
turn the right hand side linkage (D) rod 1/8 to 1/4 turn
counter-clockwise.
3.
If the unit veers to the right, loosen the jam nut (A, Figure
48) turn the right hand side linkage rod (D) 1/8 to 1/4 turn
clockwise.
4.
Re-tighten the jam nut.
5.
Drive the machine on a flat, level surface to test and repeat
steps this process as necessary.
In some cases, the tracking adjustment may not be achievable
by only adjusting the right hand side motion control rod and the
left hand motion control rod (C) must be adjusted by turning it
in the opposite direction that you turned the right hand motion
control rod. The left hand motion control rod has a limited
amount of adjustment available, and after being adjusted the
left hand lockout bolt (A, Figure 47) must fall within the notch
of the lockout plate (B) and not touch either side of the notch.
The process may need to be performed several times to get
the unit to track properly.
Right Side Lockout Bolt Adjustment
After the tracking of the unit has been adjusted the right hand
side lockout bolt (A, Figure 50) needs to be adjusted.
1.
Observe the right hand side lockout bolt. It should be
positioned so that it is in the center of the notch of the
lockout plate (C) on the ground speed control lever.
2.
To adjust the position of the right hand side lockout bolt,
move the bolt in whatever direction is necessary in the slot
of the neutral lockout shaft (B) so that it is centered in the
notch of the lockout plate (C) slot of the ground speed
control lever and re-tighten the jam nut.
Deck Lift Rods
The deck lift rods on this unit are fixed and cannot be adjusted.
Mower Deck Leveling Procedure
This unit features a rugged deck lift linkage system that can
easily be adjusted to level the mower deck.
Determining if the Mower Deck Needs to be
Leveled
1.
Park the unit on a flat, level surface. Disengage the PTO,
engage the parking brake, turn the ignition switch to OFF,
and remove the ignition key.
2.
Lock the deck in the TRANSPORT position. Place the
cutting height adjustment pin in the 4" position and lower
the deck lift lever until it contacts the cutting height
adjustment pin.
3.
Verify that the tires are inflated to the correct pressure.
4.
Verify that the mower blades are flat, and not bent or broken.
A bent or broken blade must be replaced.
WARNING
Avoid Injury! Mower blades are sharp.
Always wear gloves when handling blades or working near
blades.
5.
See Figure 51. Position the outside mower blades so they
face front-to-back.
51
6.
Measure the front tip (A, Figure 51) of the blade from the
cutting edge to the ground.
7.
Measure the rear tip (A) of the blade from the cutting edge
to the ground.
8.
Repeat the process on the other side of the machine.
• The front measurements should equal 4" (10,2 cm).
• The rear measurements should equal 4-1/4" (10,8 cm).
If the measurements do not equal the measurements as
listed above, adjust the deck leveling.
Deck Leveling Procedure
1.
Position the deck in the 4" (10.2 cm) position.
2.
Loosen the jam nuts (A, Figure 52) on all four deck linkages
(B).
52
36
Содержание 5901465
Страница 1: ...N o t f o r R e p r o d u c t i o n...
Страница 46: ...N o t f o r R e p r o d u c t i o n Notes...
Страница 47: ...N o t f o r R e p r o d u c t i o n Notes...
Страница 48: ...N o t f o r R e p r o d u c t i o n...
