background image

20

The illustration depicts the left side of the unit.

2.

Adjust the linkage rod: To increase the amount of clearance
between the handle bars and the reverse speed control
levers, turn the linkage rod (C) clockwise. To decrease the
amount of clearance between the handle bars and the
reverse speed control levers, turn the linkage rod
counter-clockwise.

3.

Once the measurement of 1" (2.54 cm) is achieved, tighten
the jam nuts against the linkage rod ball joints.

4.

Repeat the process for the other side of the unit. Both
reverse speed control levers should be adjusted
equally.

Maintenance Schedule

The following schedule should be followed for normal care of
your unit. You will need to keep a record of your operating time.

UNIT MAINTENANCE

Before each use

Check safety interlock system.

Check unit brakes.

Check unit for loose hardware.

Check hydraulic oil level.

Check tire pressures.

Every 25 Hours

UNIT MAINTENANCE

Clean debris from under rotor housing.

Check rotor blades.

Change hydraulic oil filter.*

ENGINE MAINTENANCE

Before each use

Check engine oil level.

Clean visible debris from engine compartment.

Every 50 Hours

Inspect / Clean spark arrester**.

Every 100 Hours

Check fuel filter.

Refer to engine owner's manual

Service air filter.

Change engine oil and filter.

Check / Replace spark plugs.

* More often in hot (over 85° F; 30° C) weather or dusty operating conditions.
**If equipped. Replace if damaged.

Specifications

NOTE: Specifications are correct at time of printing and are
subject to change without notice.

ENGINE

Fits model 5900520

24 Gross HP† Kawasaki

Kawasaki

Make

FX730V-DS00-S

Model

44.3 Cu. In (726 cc)

Displacement

12 volt, 15 amp charging coil; Battery:
340 cca

Electrical System

2.2 US qt. (2.1 L) w/ filter

Oil Capacity

†Power Ratings: All power levels are stated gross horsepower
per SAE J2723 as rated by Kawasaki and tested per the SAE
J1995 test standard. The gross power curves and more
information can be viewed at www.kawasaki-criticalpower.com.

CHASSIS

5 gallons (18.73 L)

Fuel Tank Capacity

Rear Wheels

20.00 X 8.00 - 10

Tire Size

15 psi (1.03 bar)

Inflation Pressure

Front Wheels

9.00 X 3.50 - 4

Tire Size

N/A (Flat Free)

Inflation Pressure

TRANSMISSIONS

ZJ-GMFE-3B5B-1RLX (5102809)

LH

21

Not 

for  

Reproduction

Содержание 5900520

























Отзывы: