Ferm COM1007P, Оригинальное руководство пользователя

Страница: 9 / 96

9
EN
• Press the spindle lock button (9) in order to
block the movement of the machine spindle.
• Keep pressing the spindle lock button (9).
Place the wrench (16) on the disk bolt and turn
it slightly until the button (9) is pushed in to the
max and the spindle rotation is blocked.
• Remove the bolt (21), small washer (20), the
big outer washer(19)
• Then remove the cutting disk (3)
Mounting a cutting disk
• In case this has not been done yet, remove the
bolt (21) by turning it counterclockwise, then
remove small washer (20) and the big outer
washer(19).
• Place the cutting disk (3) on the machine
spindle.
• First add the big outer washer (19), then the
small washer (20) and then the fixing bolt (21)
according to fig C. and tighten it by hand until
the spindle starts rotating.
• Press the spindle lock button (9) in order to
block the movement of the machine spindle.
• Keep pressing the spindle lock button (9).
Place the wrench (16) on the disk bolt and turn
it slightly in clockwise direction.
• When the spindle lock blocks the rotation,
tighten the disk bolt by using the wrench (16).
• Loosen the spindle lock button and ensure the
spindle lock button is not blocking the spindle
anymore.
Then check if the wheel is assembled correctly:
• Turn the disk (3) by hand a few rounds to check
if it is turning freely and if it is aligned well.
• Turn the machine on and let the machine run
for at least 3 minutes.
The On/Off switch
Fig. B
The On/Off switch (7) is activated by manually
pulling the switch trigger. It is cut of by releasing
the trigger again.
The workpiece clamp (5)
Fig. A & B & D
• Place the workpiece material between front
clamp (13) and rear clamp (12).
• Raise the stopper(14) like shown in Fig. D. and
rotate the screw handle (15) forward until the
front clamp (13) touches the work piece.
• Then move the stopper (14) down (to lock the
spindle) and securely fix the workpiece by
turning the screw handle (15).
Cutting at angles
Fig. E
The machine permits cutting at angles from 0
0
to
45
0
by adjusting the rear clamp (12).
• Loosen the 2 M10 hexagon socket head bolts
(22 & 23) which hold the rear clamp (12) until
the vice can move.
• Then set the rear clamp (12). to the correct
angle and tighten both bolts (22 & 23) again.
Moving the rear vice (to cut bigger work
pieces)
Fig. F
The vice permits a maximum workpiece size of
160mm when shipped from the factory. The vice
can be adjusted in to the rear to permit workpiece
size of 195 mm like shown in the right picture (fig. F).
• Loosen the 2 M10 hexagon bolts (22 & 23) on
the rear clamp (12) completely.
• Move the clamp (12) backwards and fix the
bolts (22 & 23) to the rear connection holes
again.
Adjusting the depth stop:
Fig.B
The machine is equipped with a depth stop bolt,
with this bolt the maximum cutting depth can be
adjusted.
• If the depth cutting depth needs to be
adjusted, loosen the lower nut (10B), then
adjust the depth setting by turning the upper
bolt (10A) to the desired positions.
• Then fix the lower nut (10B) again.
Cutting procedure:
In order to cut material always follow following
procedure:
• Make sure the workpiece is clamped and
supported well before starting the machine.
• Start the machine in upper position let it run for
a while until it reaches max. speed.
• Ensure the blade is turning freely without
vibration.
• Gently move down the machine until it touches
the material.
• Keep pushing the handle with little force, make
sure the blade speed is not dropping.