User’s Manual S40-R
User’s Manual S40-R
FEMA ELECTRÓNICA - Page 11
All instruments are warranted against all manufacturing
defects for a period of 24 MONTHS from the shipment date.
This warranty does not apply in case of misuse, accident or
manipulation by non-authorized personnel. In case of mal-
function get in contact with your local provider to arrange for
repair. Within the warranty period and after examination by
the manufacturer, the unit will be repaired or substituted when
found to be defective. The scope of this warranty is limited to
the repair cost of the instrument, not being the manufacturer
eligible for responsibility on additional damages or costs. .
1.14 Warranty
Manufacturer
FEMA ELECTRÓNICA, S.A.
Altimira 14 - Pol. Ind. Santiga
E08210 - Barberà del Vallès
BARCELONA - SPAIN
www.fema.es - [email protected]
Products -
S40-R
The manufacturer declares that the instruments indicated comply with the
directives and rules indicated below.
Directive of electromagnetic compatibility 2004/108/CEE
Directive of low voltage 73/23/CEE
Security rules 61010-1
Equipment “Fixed”
“Permanently connected”
Pollution degree 1 and 2 (without condensation)
Isolation Double
Category CAT-II
Emission rules
61000-6-4
Generic rule of emission
Immunity rules
61000-6-2
Generic rules of immunity
61000-4-2
By contact ±4KV - Criteria B
On air ±8KV - Criteria B
61000-4-3
Criteria A
61000-4-4
On AC power lines: ±2KV - Criteria B
On DC power lines: ±2KV - Criteria B
On signal lines : ±1KV - Criteria B
61000-4-5
Between AC power lines ±1KV - Criteria B
Between DC power lines ±0.5KV - Criteria B
61000-4-6
Criteria A
61000-4-8
30A/m at 50Hz - Criteria A
61000-4-11
0% 1 cycle Criteria A
40% 10 cycle Criteria A
70% 25 cycle Criteria B
0% 250 cycle Criteria B
Barberà del Vallès October 2009
Daniel Juncà - Quality Manager
1.16 CE declaration of conformity
1.15 Installation precautions
This instrument has been designed and verified according to the 61010-1
CE security regulation, and is designed for applications on industrial environ-
ments. See the “CE Declaration of Conformity” further in this document for
information on the category of measure and the degree of pollution levels
that apply.
Installation of this instrument must be performed by qualified personnel
only. This manual contains the appropriate information for the installation.
Using the instrument in ways not specified by the manufacturer may lead
to a reduction on the specified protection level. Disconnect the instrument
from power before starting any maintenance and / or installation action.
The instrument does not have a general switch and will start operation as
soon as power is connected. The instrument does not have protection fuse,
the fuse must be added during installation.
The instrument is designed to be panel mounted. An appropriate ventilation
of the instrument must be assured. Do not expose the instrument to excess
of humidity. Maintain clean by using a humid rag and do NOT use abrasive
products such as alcohols, solvents, etc.
General recommendations for electrical installations apply, and for proper
functionality we recommend : if possible, install the instrument far from
electrical noise or magnetic field generators such as power relays, electri
-
cal motors, speed variators, ... If possible, do not install along the same
conduits power cables (power, motor controllers, electrovalves, ...) together
with signal and/or control cables.
Before proceeding to the power connection, verify that the voltage level
available matches the power levels indicated in the label on the instrument.
In case of fire, disconnect the instrument from the power line, fire alarm
according to local rules, disconnect the air conditioning, attack fire with
carbonic snow, never with water.
Risk of electrical shock. Instrument terminals can be connected
to dangerous voltage.
Instrument protected with double isolation. No earth connection
required.
Instrument is in conformity with CE rules and regulations. See
“CE Declaration of Conformity” further in this document.