background image

Page 3

 

KataEX3-FMS 

Assembly

0.5" – 2.1"

0.5" – 1.5"

clamp to

worksurface

fit base cover

over base

flush

against

clamp

gap

Follow either

 step #1a for clamp mounting or step #1b for grommet mounting. All other steps apply to both mounting methods.

Step #1a: attach base assembly to worksurface — clamp mounting

The thickness of the worksurface must be between 0.5" and 2.1". To mount the clamp flush against 
the worksurface, the thickness must be no more than 1.5".

•  Loosen the clamp sufficiently to be able to slide it easily onto the worksurface.

•  Clamp the assembly to the worksurface in the desired position. Be sure to tighten the clamp securely.

•  Place the base cover onto the mounting post and fit the cover over the base. 

Step #1b: attach base assembly to worksurface — grommet mounting

Maximum thickness of the worksurface for grommet mounting is 1.7".

•  Place the base assembly over the grommet hole with the bolt centered.

•  Insert the grommet bar onto the grommet bolt and then screw on the grommet knob. Tighten the grommet knob securely to hold the base assembly in position.

•  Place the base cover onto the mounting post and fit the cover over the base. 

maximum thickness = 1.7"

center bolt in grommet hole

grommet base assembly

tighten grommet knob to secure

grommet bar

fit base cover

over base

Содержание ESI Kata EX3-FMS Series













Отзывы: