background image

Page 12

 KataEX 

Assembly

Step #6: 

if three monitors —

 attach center monitor arm

Below is an example of three monitor arms, which will form a row of three aligned monitors. One additional connection sleeve is used to accommodate 

the third monitor arm.

•  Remove the locking ring from the second connection sleeve. 

•  Install the sleeve about 3" above the first sleeve if the other two arms are  fixed+fixed; or about 5" above the first sleeve if the other two arms are  fixed+motion.  

(See boxed text on page 10.) The objective is to align the VESA mounts — and thereby the monitors — at the same height.

•  Secure the connection sleeve by tightening its screw with the 4mm Allen key.

•  Install the stem arm assembly onto the connection sleeve by sliding its tabs into the center two slots on the sleeve.

•  Slide the decorative covers into the four unused slots on the connection sleeve.

•  Lock the monitor arm to the connection sleeve with the locking ring. Rotate the locking ring clockwise to secure it.

4mm

Allen key

remove

locking ring

install

sleeve

install

stem arm

assembly

install

decorative

covers

install

locking

ring

Содержание esi Kata EX Series





















Отзывы: