Fein BSS 1.6, Инструкция по эксплуатации

Страница: 17 / 59

17
en
For your safety.
Read all safety warnings and all instruc-
tions.
Failure to follow the warnings
and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have thor-
oughly read and completely understood this
Instruction Manual and the enclosed “General
Safety Instructions” (document number
3 41 30 054 06 1). The documents mentioned should be
kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial safety
regulations.
Special safety instructions.
Wear personal protective equipment. Depending on the
application, use a face shield, safety goggles or safety
glasses. Wear ear protection.
The safety glasses must be
capable of protecting against flying particles generated by
the various different operations. Prolonged exposure to
high intensity noise may cause loss of hearing.
Wear protective gloves. Hot and sharp chips/swarf can
lead to injuries.
Keep the cutting tools sharp and clean. Cutting tools with
sharp cutters that have been carefully looked after are
less likely to jam and are easier to guide.
Secure the workpiece firmly.
A work piece that is gripped
tightly in a clamping device or vice, is more secure than if
held by hand.
Do not rivet or screw any name-plates or signs onto the
power tool.
If the insulation is damaged, protection against
an electric shock will be ineffective. Adhesive labels are
recommended.
Do not use accessories which are not specifically designed
and recommended by the power tool manufacturer.
Safe
operation is not ensured merely because an accessory fits
your power tool.
Clean the ventilation openings on the power tool at regular
intervals using non-metal tools.
The blower of the motor
draws dust into the housing. An excessive accumulation
of metallic dust can cause an electrical hazard.
Before putting into operation, check the mains connection
and the mains plug for damage.
Intended use of the power tool:
hand-guided slitting shears for commercial use for cutting
sheet metal, cut-outs and tight curves in weather-pro-
tected environments using the application tools and
accessories recommended by FEIN.
Operating instructions.
Guide the power tool toward the work piece only
when switched on.
Guide the power tool uniformly and with light feed in the
cutting direction. Excessive feed reduces the tool life of
the application tools.
BSS 1.6 C:
For cut-outs, pull the power tool from the chip
while the motor is running. Cut long chips off.
Do not cut steel sheets where welded. Do not cut lay-
ered sheets exceeding the max. work-piece thickness.
To increase the tool life of the blades, it is recommended
to apply a lubricating agent alongside the intended cutting
line:
– for cuts in steel sheet: cutting paste or cutting oil,
– for cuts in aluminium: Petroleum.
For inside cuts, a pilot hole is required; see technical data
for diameters.
Do not switch the power tool off until after having
removed it from the cutting path.
The symptom for worn blades is a clearly increased feed
force at lower working progress.
BSS 1.6, BSS 1.6 C: Punch and cutting bars cannot be
reground.
BSS 2.0: Punch and cutting bars can be reground.
BSS 2.0: For stationary operation, clamp the power tool
in a vice using aluminum or plastic protection jaws.
Tighten the vice adequately so that the application tool is
clamped firmly yet not damaged.
Repair and customer service.
Blow out the interior of the power tool at
regular intervals from outside through the air
vents with dry, compressed air.
Check the application tool for wear every hour.
If the supply cord of this power tool is damaged it must
be replaced by a specially prepared cord available
through the FEIN customer service centre.
If required, you can change the following parts yourself:
Application tools, Cutting bars
Warranty and liability.
The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer’s warranty declaration.
Only part of the accessories described or shown in this
instruction manual will be included with your power
tool.
Declaration of conformity.
FEIN declares itself solely responsible for this product
conforming with the documents and standards given on
the last page of this Instruction Manual.
Environmental protection, disposal.
Packaging, worn out power tools and accessories should
be sorted for environment-friendly recycling.
WARNING
3 41 01 111 06 0.book Seite 17 Donnerstag, 10. April 2008 8:11 08