Federal Signal Corporation UltraVoice UVRI-B Series Скачать руководство пользователя страница 44

Страница: 44 / 56

Operations

UltraVoice Remote Interface (UVRI-B)

Federal Signal www.fedsig.com

Indicators

Table 25 Indicators on the Control Board (See Figure 10)

TC Interface GND Fault

D10

TC Interface Line Fault

D11

TC Interface TC2-4 / Spare #6 Input

D15

TC Interface TC2-1 / Spare #3 Input

D16

TC Interface TC2-2 / Spare #4 Input

D17

TC Interface TC2-3 / Spare #5 Input

D35

TC Interface TC1-2 Output

D36

TC Interface TC1-3 Output

D37

TC Interface TC1-4 Output

D40, D41, D42 RECEIVE LEVEL, 3 stage LED bar graph
D44

RXD Receive Serial Data and receipt of radio channel modulation

D45

TXD Transmit Serial Data and DTMF and Digital

D46

CARRIER

RF Carrier Indicator on with carrier present

D49

TX PTT

D50

ARM Unit Armed Indicator

D51

Public Address mode Indicator

D52

CPU Microcontroller Heartbeat

D53

AUDIO A, Audio present on Channel A

D54

AUDIO B, Audio present on Channel B

D55

Fault

D56

Power

D59

TC Interface TC1-1 Output

D74

ISO +5V

D85

Rotation Relay Active

D89

Relay #1 Output Active

D92

Relay #2 Output Active

D86

ISO 12V

D105

Relay #3 Output Active

D107

Relay #4 Output Active

D118

Battery Charging

Table 26 Indicators on the Amplifier Board

ARM

Output Current Indicator

Output Voltage Indicator

Amp Fault

D12

Speaker Line Fault

D13

Power

Содержание UltraVoice UVRI-B Series

























































Результаты поиска

Содержание UltraVoice UVRI-B Series

Отзывы:

Federal Signal Corporation UltraVoice UVRI-B Series, Описание, характеристики, установка и руководство по эксплуатации, Страница: 44 / 56

Результаты поиска

Содержание UltraVoice UVRI-B Series

Отзывы: