manualshive.com logo in svg

Federal Signal Corporation UltraVoice UVRI-B Series, Описание, характеристики, установка и руководство по эксплуатации, Страница: 42 / 56

Поделиться
Скачать
Federal Signal Corporation UltraVoice UVRI-B Series Скачать руководство пользователя страница 42

42

  

  

Operations

UltraVoice Remote Interface (UVRI-B) 

Federal Signal www.fedsig.com

Table 21 Connectors on the Amplifier Board (See Figure 9)

JP2

Speaker Output 

1 To Control board JP34 1 and 4

2 To Speaker Common

JP3 (Line C) Balanced Audio Line Input

1 and 2 1.33 to 10/25 V

rms

 Audio Output (JP6) on the Control board

JP4

Audio Input Level Select

 

1 and 2 – 1.33 V

rms

 line level

 

3 and 4 – 10 V

rms

 

5 and 6 – 25 V

rms

JP5 (Line B)

I

2

C port to I

2

C port (JP19) on Control board

JP7

Disable Line Fault

Shorted to disable speaker line fault detection

JP8 (Line A)

DC Power Input

 

1 Ground – To JP21 (Amp -)

 

2 +12.0 Vdc – To JP21 (Amp +)

JP9

Balanced Audio Line Output

JP10

Shorted when amplifier is NOT used in Stand-Alone mode

VR1

Volume Control

Configuration Jumpers

Table 22 Configuration Jumpers on the Control Board (See Figure 10)

JP1

Dual transceiver priority jumper

Jumper XCVR1 side to give transceiver #1 priority

Jumper XCVR2 side to give transceiver #2 priority

Jumper neither side, first carrier detect has priority

JP2

Transceiver #1 VOX Jumper

Short to use VOX for Carrier Detect

JP3

Short to force Carrier Detect of transceiver 1

JP11

600 Ω I/O Input Configuration Jumper Pins:   

2-3  600 Ω audio in to receiver decoders  

1-2  Audio from 600 Ω sent to amplifier when 600 Ω PTT is closed

JP12

600 Ω I/O Output Configuration Jumper Pins:

1-2  

Output siren audio

2-3 

Output radio transmit audio

JP13

10 V/25 V Output Configuration Jumper Pins:

1-2 

25 V Output

2-3 

10 V Output

JP15

Voice Output Configuration Jumper Pins:

1-2 

Normal Equalization

2-3 

Treble Boost

JP16

Fast DTMF Decode. Short for fast timing.

JP17

Disable Digital Receive. Short to disable.

JP20

Siren Audio Channel Select Jumper:

1-2 

Signal 0, A

2-3 

Signal 1, B

Содержание UltraVoice UVRI-B Series

























































Отзывы:

Нет отзывов