Federal Signal Corporation UltraVoice UVRI-B Series Скачать руководство пользователя

Страница: 37 / 56

Operations

Description, Specifications, Installation, and Operation Manual

Federal Signal

www.fedsig.com

User Programs

The UVRI-B has the capacity to store functions for specific alerting configuration. Use

functions to activate relays for control of external devices and activation of pre-recorded

messages. See the Commander Software Manual and the Informer-IP Setup, Program,

and User Manual.

Status Monitoring

The UVRI-B provides system monitoring with automatic or manual reporting of system

operation and status. The following items are monitored:
•  System operation
•  Audio Output
•  Input voltage
•  Charger/battery status
•  Intrusion
•  Local activations

Connectors, Configuration Jumpers, Test Points, Controls and Indicators

The following table provides settings and interface inputs and outputs for the control card.

Table 20 Connectors on the Control Board (See Figure 9)

Microphone jack (Part Number MNC-MC)

10 kΩ input impedance,

50 mV

p-p

nominal input level

Options Connector:

1-2

Enable Ethernet Port

9-10 Change Serial ports 1 and 2 from 1200 baud to 115200 and 9600

baud Respectively.

JP5 and JP4 Transceiver #1 and #2 Ports
JP6 (Line C) 10 V/25 V, 0.7 W Audio output (to Amp JP3 Audio Input)
JP7

microSD FLASH card holder

JP8

600 Ω I/O Control and PA Input

Siren and TX Audio Output – Balanced

Typically used with landline application

TC1 Output

600 Ω Audio Signal

TC1 Input

600 Ω Audio Sense

JP9

600 Ω Audio Sense Input – Balanced

Jumpered to JP10 when not used

Typically used for fire panel interface

JP10

600 Ω Audio Signal Output – Balanced

Typically used for fire panel interface

Содержание UltraVoice UVRI-B Series

























































Результаты поиска

Содержание UltraVoice UVRI-B Series

Отзывы:

Похожие инструкции для UltraVoice UVRI-B Series

Бренды по названию

Популярные бренды

Federal Signal Corporation UltraVoice UVRI-B Series, Описание, характеристики, установка и руководство по эксплуатации

Результаты поиска

Содержание UltraVoice UVRI-B Series

Отзывы:

Похожие инструкции для UltraVoice UVRI-B Series

Бренды по названию

Популярные бренды