manualshive.com logo in svg

Federal Signal Corporation DSA1X, Описание, характеристики и руководство по установке

Поделиться
Скачать
Federal Signal Corporation DSA1X Скачать руководство пользователя страница 19

19

Getting Service

Description, Specifications, and Installation Manual

Tapping the Speaker

The DSA1X can be tapped for lower power levels. 
To tap the speaker:
1.  Open the speaker.
2.  Use the quick connect connectors to tap to the desired power level. Leave one quick 

connect connected to COM and connect the speaker lead to one of the following taps: 

18 W, 32 W, 55 W, or 100 W.

Figure 14 Tapping the Speaker Drawing

Tap Settings

COMCOM

25V

70V

LINE IN

COM

25V

70V

LINE OUT

14.2V

9.8V

COM

20.0V 28.3V

18W

32W

55W

100W

Closing the Housing

To close the housing, do the following:
1.  Verify that the cover gasket is in the groove around the perimeter of the rear cover. 
2.  If the front of the unit was removed, lift the front of the DSA1X to allow the hinge 

pin to be installed, align the front unit with the rear cover and attach the hinge pin 

with retaining clip. 

3.  Verify that the wires are not strained and are not impeding ability to close unit. 
4.  Lift front of unit and seat the front cover against the rear enclosure. 
5.  Tighten the cover screws hand tight, and then torque them in alternate pattern to  

60 in-lb +/- 10 in-lb.

Getting Service

If you are experiencing any difficulties, contact Federal Signal Customer Care at:  

800-548-7229 or 708-534-3400 extension 5822 or Technical Support at: 800-524-3021 

or 708-534-3400 extension 7329 or through e-mail at: [email protected]. For 

instruction manuals and information on related products, visit: http://www.fedsig.com/

Содержание DSA1X





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды