manualshive.com logo in svg

Federal Signal Corporation Allegiant Series, Инструкция по установке, обслуживанию и ремонту

Поделиться
Скачать
Federal Signal Corporation Allegiant Series Скачать руководство пользователя страница 20

20   

20   

Allegiant Light Bar 

Federal Signal 

www.fedsig.com

Wiring the Allegiant Light Bar

7.  Separate all electronic equipment wiring from two-way radio equipment wiring.
8.  To avoid interference, keep two-way radio antennas a minimum of 18 inches (45.7 

cm) away from warning equipment.

9.  Whenever possible, run full wire lengths. DO NOT splice the wires.
10. Do not coil excess wire. Leave a drain loop for servicing.

DRILLING PRECAUTIONS: Before drilling holes, check the area into which 

you plan to drill to ensure that you do not damage vehicle components. All 

drilled holes should be deburred and all sharp edges should be smoothed. 

Additionally, all exterior drilled holes must be sealed with Motorcraft seam 

sealer T-A-2-B or equivalent to prevent the potential exposure to carbon 

monoxide or other potentially harmful fumes. Failure to observe this warning 

could cause serious injury or death.

11.  When you frame-ground the equipment, use the manufacturer-supplied ground 

locations in the vehicle.

IMPORTANT: After the installation, frequently inspect the light bar and mounting feet 

to ensure that all fasteners and brackets are tight. 

Connecting Power to the Light Bar 

NOTE: Plan the location of the wire-routing hole in the vehicle roof so that the power 

and communication cables do not have tight bends and have some slack to ease 

removal. 

BATTERY EXPLOSION: To avoid a battery explosion, always disconnect the 

negative battery cable first and reconnect it last. Avoid causing a spark when 

connecting near or to the battery. The gases produced by a battery can cause 

a battery explosion that could result in vehicle damage and serious injury.

SEAT REMOVAL PRECAUTION: If a vehicle seat is temporarily removed, verify 

with the vehicle manufacturer if the seat needs to be recalibrated for proper 

airbag deployment. Failure to follow this warning cause serious injury or 

death.

REVERSE POLARITY / MISWIRING: Reverse polarity or incorrect voltage may 

damage the light. To avoid damage to the light, ensure that the battery voltage 

is the same as the voltage rating of the light and that the correct polarity 

is observed. If you are connecting to a cigarette lighter plug or 12 V outlet, 

connect the positive wire to the center terminal and connect the negative wire 

to the outer terminal.

Содержание Allegiant Series





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды