manualshive.com logo in svg

Feasa Low Light LED Analyser, Руководство пользователя, Страница: 28 / 74

Поделиться
Скачать
Feasa Low Light LED Analyser Скачать руководство пользователя страница 28

FEASA LED ANALYSER LOW LIGHT
FUNCTIONAL VERSION 

Get Data Mode

getABSINT@@ Get the Absolute Intensity Value of the Led under test.

Transmit

Receive

Getabsint@@

getabsintall

#.####e±##

Where:

@@

represents the Fiber Number and is a number in the range 01 – 10.

all

represents the 10 Fibers in a Feasa 10A, or 3 Fibers in a 3A.

#.####e±##

represents the Intensity reading

Description:

This command will allow the user to interrogate the Led Analyser to return the absolute 
Intensity Value for the Led under test at Fiber@@. 

This command should only be used in conjunction with the Feasa LED Spectrometer.  

Absolute Intensity values must first be measured with the Spectrometer.   The LED Analyser 
must then be calibrated with these values using the programs supplied with the Spectrometer. 

Alternatively use the 

getabsintall

 command to read back the LED data for all 10 leds

in one command.

Example:

Place fiber 01 over the Led to be tested. Using any of the  

Capture  

commands, capture the

data for that Led.  Type the command 

getabsint01

 and the analyser will respond with with

the intensity reading in the format 

#.####e±##

getabsint01
2.5000e-02

Back to Index

28

Содержание Low Light LED Analyser











































































Отзывы:

Нет отзывов