Feasa 10-F Скачать руководство пользователя страница 31

Страница: 31 / 132

FEASA LED ANALYSER
FUNCTIONAL VERSION

Get Data Mode

getWAVELENGTH##

- Get the Dominant Wavelength

Transmit

Receive

getwavelength##

getwavelengthall

XXX

Where:

represents the Fiber Number and is a number in the range 1 – 20.

all

represents the 20 Fibers in a Feasa 20F, or 3 Fibers in a 3F.

xxx

represents the dominant wavelength of the LED in nanometers.

Description

This command is used to get the value of the Dominant Wavelength for the LED under the

Fiber number

This command should be preceded by the

capture C

command to ensure valid LED data is

stored in the memory of the LED Analyser. The

C1-C5

commands are available but are not as

accurate. The data for each LED can be read out one-at-the-time, in any order.

Alternatively use the

getwavelengthall

command to read back the LED data for all 20

leds in one command.

Example:

The PC transmits

getwavelength01

to the LED Analyser to instruct it to send the stored

dominant wavelength for the LED positioned under Fiber No 1. The LED Analyser will return a

string

xxx

to the PC.

getwavelength01

513

Back to Index

Содержание 10-F





































































































































Результаты поиска

Содержание 10-F

Отзывы:

Бренды по названию

Популярные бренды

Feasa 10-F, Руководство пользователя

Результаты поиска

Содержание 10-F

Отзывы:

Бренды по названию

Популярные бренды