Feasa 10-F Скачать руководство пользователя страница 23

Страница: 23 / 132

FEASA LED ANALYSER
FUNCTIONAL VERSION

Capture Mode

CAPTUREMULTI - Multiple Capture Command

Transmit

Receive

setrange@@#

putrange@@#

getrange@@

capturemulti

OK
OK

1 to 5

Where:

represents the fiber number in the range 01 – 20.

represents the capture range 1 - 5

Description

The

capturemulti

command will capture the LED data for the specified fiber at the

specified range.

The

setrange@@#

putrange@@#

commands will set the required range for each declared

individual fiber. The

getrange@@

will return the range the user has enables for this fiber.

Example:

The DUT has 5 leds with 5 very different intensity values. You can now specify fiber 1 to range

Ultra (C5), Fiber 2 to range Super (C4), Fiber 3 to range High (C3), Fiber 4 to range Medium
(C2) and Fiber 5 to range Low (C1). Do one

capturemulti

command to get your 5

readings.

Putrange015

(Fiber 1, Range Ultra / 5)

putrange024

(Fiber 2, Range Super / 4)

putrange033

(Fiber 3, Range High / 3)

putrange042

(Fiber 4, Range Medium / 2)

putrange051

(Fiber 5, Range Low / 1)

capturemulti

Back to Index

Содержание 10-F





































































































































Результаты поиска

Содержание 10-F

Отзывы:

Бренды по названию

Популярные бренды

Feasa 10-F, Руководство пользователя

Результаты поиска

Содержание 10-F

Отзывы:

Бренды по названию

Популярные бренды