FAZUA RIDE 50 TRAIL/STREET Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 32

FAZUA RIDE 50 TRAIL/STREET Скачать руководство пользователя страница 6

English | Assembly instructions

6

BOTTOM BRACKET

Provided screws:

•  Gear screws (RIDE 50 screw BB mount)
•  Lockring
•  Fixing screws of the BOTTOM BRACKET cover

Tool installation:

Tool removal:

•  Torx screwdriver T30
•  Bottom bracket tool* 20 teeth
•  Torque spanner
•  Needle nose pliers

•  Torx screwdriver T30
•  Bottom bracket tool* 20 teeth
•  Torque spanner
•  Needle nose pliers
•  Chain whip (optional)
•  Crank puller tool ISIS** (optional)

* The bottom bracket tool must have a minimum inner diameter of 24.1 mm.

** The ISIS crank puller tool is only required if the e-bike does not have cranks with an integrated puller.

Speed sensor and spoke magnet

Provided screws:

• Fixing screw
• Spoke screw

Tool installation:

Tool removal:

•  Torx screwdriver T20
•  Phillips screwdriver PH2
•  Needle nose pliers
•  Torque spanner

•  Torx screwdriver T20
•  Phillips screwdriver PH2
•  Needle nose pliers

2 ABOUT THESE ASSEMBLY INSTRUCTIONS

These assembly instructions (hereinafter referred to as the “manual”) belong to the FAZUA RIDE 50 drive
system and are intended specifically for FAZUA dealers and trained specialist and service personnel.
The manual describes all the necessary steps to install the components of the drive system in the e-bike or
to remove the installed components from the e-bike.
The manual is expressly not designed for use by laypersons or as an alternative/supplement to the original
operating instructions.
To highlight hazards or risks, as well as important additional information within the manual, the following
markings are used:

WArninG

Risks that could result in death or serious injury are identified with the signal word “Warning”.

notice

Risks relating to assembly errors or damage to the product are marked with the signal word “NOTE”.

«
...
4
5
6
7
8
...
»

Содержание RIDE 50 TRAIL/STREET

































Отзывы:

Нет отзывов