Fayat DYNAPAC F1800C Скачать руководство пользователя страница 171 | Manualshive

Страница: 171 / 330

background image

D 30.18 37

Installation and operation

- Install the bracket (1) at the vehicle step (3) using the corresponding assembly ma-

terial (2).

- Fasten the illuminated balloon (4) to the holding tube (5) and tighten the clamping

bolt (6).

- Guide the holding tube (5) into the premounted holder (1) and tighten the clamping

lever (7) correctly to fix the holding tube.

- With one hand on the handle flagged in green (8), pull down hard to open the bal-

loon before putting it into operation.
When the balloon has been pulled down completely as far as it will go, a safety
brace (9) hinges out of the guide rod.

- Once the illuminated balloon is completely mounted and secured, connect

the plug (10) of the illuminated balloon in the corresponding switch cabinet
sockets (11).

m

Never adjust the holding tube while the illuminated balloon is in operation.

A

Operation of the switch cabinet - see screed operating instructions.

m

Route the supply lines so as to rule out any risk of stumbling or damage to the lines.

Danger due to electric shock

Electric shock can cause severe or fatal injuries
- The Powermoon must always be completely unpacked,

assembled and aligned before it is connected to the
power grid and switched on!

Danger of squeezing!

Fingers or hands can get clamped between the bracket and
the holding tube!

- Caution when inserting the holding tube!

CAUTION

CAUTION

«
...
169
170
171
172
173
...
»

Содержание DYNAPAC F1800C











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DYNAPAC F1800C

Бренд: Konica Minolta Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды