Fayat DYNAPAC F1800C Скачать руководство пользователя страница 144 | Manualshive

Страница: 144 / 330

background image

D 30.18 10

Driver's seat, type I

f

To avoid damage to health, the individu-
al seat settings should be checked and
adjusted before starting the vehicle.

f

After locking the individual elements, it
must no longer be possible to shift then
to another position.

-

Weight setting (1):

The relevant driv-

er's weight should be set by turning
the weight adjustment lever when the
driver's seat is unoccupied.

-

Weight indicator (2):

The set driver's

weight can be read off at the viewing
window.

-

Longitudinal adjustment (3):

Longi-

tudinal adjustment is released by actu-
ating the locking lever.
The locking lever must engage in the desired position.

-

Seat depth adjustment (4):

The seat depth can be individually adjusted. Raise the

button to adjust the seat depth. The desired position is set by simultaneously sliding
the seat surface forwards or backwards.

-

Seat inclination adjustment (5):

The seat surface's longitudinal inclination can be

individually adjusted. Raise the button to adjust the inclination. The seat surface in-
clines to the desired position by simultaneously loading or relieving it.

-

Armrest inclination (6):

The armrest's longitudinal inclination can be adjusted by

turning the hand wheel. Turning outwards raises the front of the armrest; turning
inwards lowers it at the front.
In addition, the armrests can be folded up fully.

-

Lumbar support (7):

Both the height and the extent of the convexity in the backrest

padding can be individually adjusted by turning the hand wheel to the left or right.

-

Backrest adjustment (8):

The backrest is adjusted via the locking lever. The lock-

ing lever must engage in the desired position.

-

Back extension (9):

By pulling out via perceptible detents, the height can be indi-

vidually adjusted up to a limit stop. To remove the back extension, the limit stop is
overcome with a jolt.

-

Seat heating ON/OFF (10):

The seat heating is switched on and off by actuating

the switch.

-

Seat belt (11):

The seat belt must be applied before starting up the vehicle.

f

The seat belts must be replaced following an accident.

3

7

10

4

5

6

6

8

11

1

9

2

«
...
142
143
144
145
146
...
»

Содержание DYNAPAC F1800C











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DYNAPAC F1800C

Бренд: Porter-Cable Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды