Fayat DYNAPAC DFP8 Скачать руководство пользователя страница 94

Страница: 94 / 110

8.9.3 Cleaning the water spraying system

Park the machine in secured condition

Chapter 6.5

‘Parking the machine in secured condition’ on page 62

Remove the cap (1) from the water tank.

Remove the rubber caps (3) from the spray tube.

Open shut-off valve (2) and drain off all water.

Flush the water tank with a strong water jet, until all dirt has

run out.

Plug the rubber caps back on the spray tube.

Fill the water tank with clean water and close the cap.

8.9.4 Servicing the V-belt

Protective equipment:

Working clothes

Safety shoes

Protective gloves

Park the machine safely

Chapter 6.5 ‘Parking the machine

in secured condition’ on page 62

Allow the engine to cool down.

Loosen the fastening screws (2) and remove the V-belt guard

(1).

Check condition and tension of the V-belt, tighten if neces-

sary.

Compression measurement:

approx. 5 mm (0.2 in).

If necessary, tighten the V-belt; if damaged, replace the V-

belt

Chapter 8.8.3 ‘Replacing the V-belt’ on page 82

Fig. 97

B-834-0144

Fig. 98

Fig. 99

Maintenance – As required

DFP8

Содержание DYNAPAC DFP8















































































































Результаты поиска

Содержание DYNAPAC DFP8

Отзывы:

Похожие инструкции для DYNAPAC DFP8

Бренды по названию

Популярные бренды

Fayat DYNAPAC DFP8, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание DYNAPAC DFP8

Отзывы:

Похожие инструкции для DYNAPAC DFP8

Бренды по названию

Популярные бренды