Fayat DYNAPAC DFP8 Скачать руководство пользователя страница 80

Страница: 80 / 110

8.8 Annually

8.8.1 Replacing the spark plug

NOTICE!
Danger of engine damage!

–

Do not use spark plugs with incorrect heat

value.

Recommended spark plugs:

NGK

BPR6ES

DENSO

W20EPR-U

Protective equipment:

Working clothes

Protective gloves

Special tool:

13/16 inch spark plug spanner

Park the machine in secured condition

Chapter 6.5

‘Parking the machine in secured condition’ on page 62

Allow the engine to cool down for at least 15 minutes.

Clean the area around the spark plug.

Unscrew the spark plug using a 13/16 inch spark plug

spanner.

Check the electrode gap of the new spark plug with a feeler

gauge, if necessary, adjust the gap.

Nominal value:

0.7 - 0.8 mm (0.028 - 0.032 in)

Screw in the new spark plug carefully by hand.

Once the sealing surface of the new spark plug is in contact,

tighten for another 1/2 turn with the spark plug spanner.

8.8.2 Checking, adjusting the valve clearance

NOTICE!
Danger of engine damage!

We recommend to have this work carried out by

trained personnel or our after sales service.

–

Before checking the valve clearance let the

engine cool down.

Fig. 66

Maintenance – Annually

DFP8

Содержание DYNAPAC DFP8















































































































Результаты поиска

Содержание DYNAPAC DFP8

Отзывы:

Похожие инструкции для DYNAPAC DFP8

Бренды по названию

Популярные бренды

Fayat DYNAPAC DFP8, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание DYNAPAC DFP8

Отзывы:

Похожие инструкции для DYNAPAC DFP8

Бренды по названию

Популярные бренды