Fayat DYNAPAC DFP8 Скачать руководство пользователя страница 32

Страница: 32 / 110

3.9 Maintenance work

3.9.1 Preliminary remarks

Always carry out the prescribed maintenance work and mainte-

nance measures on time in order to maintain the safety, opera-

tional readiness and long service life of the machine.

The machine must only be serviced by qualified personnel author-

ised by the operating company.

3.9.2 Working on the engine

Drain the engine oil at operating temperature – danger of scalding!

Wipe off spilled oil, catch running out oil and dispose of environ-

mentally.

When working on the air filter no dirt should fall into the air duct.

Do not work on the hot exhaust - danger of burning!

Store used filters and other oil contaminated materials in a sepa-

rate, specially marked container and dispose of environmentally.

3.9.3 Cleaning work

Do not perform cleaning work while the motor is running.

Allow the engine to cool down before starting cleaning work.

Do not use gasoline or other easily inflammable substances for

cleaning.

3.9.4 Measures for longer shut-down periods

If the machine is taken out of operation for a longer period of time,

various conditions must be met and maintenance work must be

carried out both before and after shut-down

Chapter 8.9.7

‘Measures prior to extended shut-down period’ on page 97

It is not necessary to define a maximum storage period if these

measures have been performed.

3.9.5 After maintenance work

Reassemble all guards and protections.

Concerning your safety – Maintenance work

DFP8

Содержание DYNAPAC DFP8















































































































Результаты поиска

Содержание DYNAPAC DFP8

Отзывы:

Похожие инструкции для DYNAPAC DFP8

Бренды по названию

Популярные бренды

Fayat DYNAPAC DFP8, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание DYNAPAC DFP8

Отзывы:

Похожие инструкции для DYNAPAC DFP8

Бренды по названию

Популярные бренды