Fayat DYNAPAC DFP8 Скачать руководство пользователя страница 19

Страница: 19 / 110

Examples for improper use are:

dragging the machine along as a measure of transportation

throwing the machine off the transport vehicle

attaching an additional weight to the machine

It is not permitted to stand on the machine while working.

Lifting tackle must be removed before starting work.

Starting and operating the machine in explosive environments and

in underground mining is prohibited.

The lifting and lashing points specified in these instructions must

be used. It is prohibited to use other lifting and lashing points (e.g.

guide handle, steering rod).

3.1.6 Estimated service life of the machine

If the following general conditions are met, the estimated service

life of the machine is usually in the range of several thousand oper-

ating hours:

Regular safety inspections by an expert / qualified person

Performance of the prescribed maintenance work within the

specified time

Immediate performance of necessary repair work

Exclusive use of original spare parts

Concerning your safety – Basic prerequisites

DFP8

Содержание DYNAPAC DFP8















































































































Результаты поиска

Содержание DYNAPAC DFP8

Отзывы:

Похожие инструкции для DYNAPAC DFP8

Бренды по названию

Популярные бренды

Fayat DYNAPAC DFP8, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание DYNAPAC DFP8

Отзывы:

Похожие инструкции для DYNAPAC DFP8

Бренды по названию

Популярные бренды