Fayat Dynapac DFP6 Скачать руководство пользователя страница 88

Страница: 88 / 116

Hold the hexagon nut (1) on the rocker arm and loosen

counter nut (2).

Adjust the hexagon nut, until the feeler gauge can be

inserted and pulled out with little resistance after retightening

the counter nut.

Install the valve cover (2) with a new seal (3).

Tighten the fastening screws (1) evenly.

8.8.3 Cleaning the slurry filter and fuel strainer

DANGER!
Danger to life caused by explosive gas-air

mixes!

–

Do not allow gasoline to come into contact with

hot components.

–

Smoking and open fire is prohibited.

–

Keep away from heat sources, sparks and

other sources of ignition.

–

Do not spill any gasoline.

Protective equipment:

Working clothes

Protective gloves

Park the machine in secured condition

Chapter 6.6

„Parking the machine in secured condition“ on page 67

Allow the engine to cool down.

Adjusting the valve clearance

Fig. 69

Final work

Fig. 70

Maintenance – Annually

DFP6

Содержание Dynapac DFP6





















































































































Результаты поиска

Содержание Dynapac DFP6

Отзывы:

Бренды по названию

Популярные бренды

Fayat Dynapac DFP6, Инструкция по эксплуатации

Результаты поиска

Содержание Dynapac DFP6

Отзывы:

Бренды по названию

Популярные бренды