Fayat Dynapac DFP6 Скачать руководство пользователя страница 112

Страница: 112 / 116

10.1 Final shut-down of machine

If the machine can no longer be used and needs to be finally shut

down you must carry out the following work and have the machine

disassembled by an officially recognized specialist workshop.

DANGER!
Danger to life caused by explosive gas-air

mixes!

–

Do not allow gasoline to come into contact with

hot components.

–

Smoking and open fire is prohibited.

–

Keep gasoline away from heat sources, sparks

and other sources of ignition.

–

Do not spill any gasoline.

–

Components that previously contained gaso-

line must not be cut with a cutting torch.

WARNING!
Health hazard caused by fuels and lubricants!

–

Safety regulations and environmental protec-

tion regulations must be followed when han-

dling fuels and lubricants

Chapter 3.4 „Han-

dling fuels and lubricants“ on page 25

Protective equipment:

Working clothes

Safety shoes

Protective gloves

Safety goggles

Empty the fuel tank.

Drain engine oil from engine and exciter housing.

Disposal – Final shut-down of machine

DFP6

112

Содержание Dynapac DFP6





















































































































Результаты поиска

Содержание Dynapac DFP6

Отзывы:

Бренды по названию

Популярные бренды

Fayat Dynapac DFP6, Инструкция по эксплуатации

Результаты поиска

Содержание Dynapac DFP6

Отзывы:

Бренды по названию

Популярные бренды