Fayat Dynapac DFP6 Скачать руководство пользователя страница 101

Страница: 101 / 116

8.9.6 Checking, cleaning the spark plug

NOTICE!
Danger of engine damage!

–

Do not use spark plugs with incorrect heat

value.

Protective equipment:

Working clothes

Protective gloves

Special tool:

13/16 inch spark plug spanner

Park the machine in secured condition

Chapter 6.6

„Parking the machine in secured condition“ on page 67

Allow the engine to cool down for at least 15 minutes.

Clean the area around the spark plug.

Unscrew the spark plug using a 13/16 inch spark plug

spanner.

Check the condition of the spark plug, clean if necessary.

In case of excessive combustion residues or burned off elec-

trodes, replace the spark plug

Chapter 8.8.1 „Replacing

the spark plug“ on page 86

Check the electrode gap of the spark plug with a feeler

gauge, if necessary, adjust the gap.

Nominal value:

0.7 - 0.8 mm (0.028 - 0.032 in)

Carefully screw in the spark plug by hand.

Once the sealing surface of the used spark plug is in contact,

tighten for another 1/8 to 1/4 turn with the spark plug

spanner.

NOTICE!
Danger of engine damage caused by a loose

spark plug!

–

Always screw the spark plug in correctly.

Fig. 101

Fig. 102

Maintenance – As required

DFP6

101

Содержание Dynapac DFP6





















































































































Результаты поиска

Содержание Dynapac DFP6

Отзывы:

Бренды по названию

Популярные бренды

Fayat Dynapac DFP6, Инструкция по эксплуатации

Результаты поиска

Содержание Dynapac DFP6

Отзывы:

Бренды по названию

Популярные бренды