Fayat BOMAG BVP 10/36 Скачать руководство пользователя

Страница: 97 / 112

8.9.7 Measures for longer shut-down periods

8.9.7.1

Measures before shutting down

DANGER!
Danger to life caused by explosive gas-air

mixes!

–

Do not allow gasoline to come into contact with

hot components.

–

Smoking and open fire is prohibited.

–

Keep away from heat sources, sparks and

other sources of ignition.

–

Do not spill any gasoline.

If the machine is shut down for a longer period of time, e.g. winter

season, the following work must be carried out.

Depending on weather conditions these conservation measures

will protect the machine for approx. 6 to 12 months.

Park the machine in secured condition

Chapter 6.5

„Parking the machine in secured condition“ on page 62

Allow the engine to cool down for at least 30 minutes.

Clean the machine thoroughly.

Change the engine oil

Chapter 8.7.1 „Changing the engine

oil“ on page 79

Use fuel stabilizer or drain off fuel completely.

Mix fresh fuel with fuel stabilizer (follow the instructions of the

manufacturer).

Empty the fuel tank and fill it with the prepared fuel mix.

Start the engine and run the machine for approx. 10 minutes

in the open.

Park the machine in secured condition.

Close the fuel valve.

Using fuel stabilizer

Emptying the fuel tank.

Fig. 101

Maintenance – As required

BVP 10/36

Содержание BOMAG BVP 10/36

















































































































Результаты поиска

Содержание BOMAG BVP 10/36

Отзывы:

Похожие инструкции для BOMAG BVP 10/36

Бренды по названию

Популярные бренды

Fayat BOMAG BVP 10/36, Инструкция по эксплуатации

Результаты поиска

Содержание BOMAG BVP 10/36

Отзывы:

Похожие инструкции для BOMAG BVP 10/36

Бренды по названию

Популярные бренды