Fayat BOMAG BVP 10/36 Скачать руководство пользователя

Страница: 72 / 112

8.2.2.2

Fuel stabilizer

If the machine is only occasionally used (if it is out of use for longer

than four weeks), mix in the correct amount of fuel stabilizer

directly after you have purchased fresh fuel.

The fuel stabilizer has a limited shelf life.

Please follow the instructions of the manufacturer concerning the

correct mixing ratio and shelf life.

Mixing in fuel stabilizer does not regenerate old fuel.

8.2.3 Oil for exciter shaft housing

Use only engine oils according to the following specifications:

API CI-4 or higher quality

Avoid mixing engine oils.

NOTICE!
Components may get damaged!

–

Do not use low-ash engine oils for the exciter

shaft housing.

Maintenance – Fuels and lubricants

BVP 10/36

Содержание BOMAG BVP 10/36

















































































































Результаты поиска

Содержание BOMAG BVP 10/36

Отзывы:

Похожие инструкции для BOMAG BVP 10/36

Бренды по названию

Популярные бренды

Fayat BOMAG BVP 10/36, Инструкция по эксплуатации

Результаты поиска

Содержание BOMAG BVP 10/36

Отзывы:

Похожие инструкции для BOMAG BVP 10/36

Бренды по названию

Популярные бренды