Fayat Group Dynapac DFP11 Скачать руководство пользователя страница 99

Страница: 99 / 114

Clean the area around the spark plug.

Unscrew the spark plug using a 13/16 inch spark plug

spanner.

Check the condition of the spark plug, clean if necessary.

In case of excessive combustion residues or burned off elec-

trodes, replace the spark plug

Chapter 8.8.1 „Replacing

the spark plug“ on page 84

Check the electrode gap of the spark plug with a feeler

gauge, if necessary, adjust the gap.

Nominal value:

0.7 - 0.8 mm (0.028 - 0.032 in)

Carefully screw in the spark plug by hand.

Once the sealing surface of the used spark plug is in contact,

tighten for another 1/8 to 1/4 turn with the spark plug

spanner.

NOTICE!
Danger of engine damage caused by a loose

spark plug!

–

Always screw the spark plug in correctly.

8.9.6 Measures for longer shut-down periods

8.9.6.1

Measures before shutting down

DANGER!
Danger to life caused by explosive gas-air

mixes!

–

Do not allow gasoline to come into contact with

hot components.

–

Smoking and open fire is prohibited.

–

Keep away from heat sources, sparks and

other sources of ignition.

–

Do not spill any gasoline.

If the machine is shut down for a longer period of time, e.g. winter

season, the following work must be carried out.

Fig. 98

Fig. 99

Maintenance – As required

DFP11

Содержание Dynapac DFP11



















































































































Результаты поиска

Содержание Dynapac DFP11

Отзывы:

Fayat Group Dynapac DFP11, Руководство по эксплуатации, Страница: 99 / 114

Результаты поиска

Содержание Dynapac DFP11

Отзывы: