Fayat Group Dynapac DFP11 Скачать руководство пользователя страница 93

Страница: 93 / 114

Tilt the machine slightly towards the oil drain side and sup-

port it safely.

Unscrew the oil drain plug (1) and collect running out oil.

Stand the machine upright.

NOTICE!
Components may get damaged!

Do not use low-ash engine oils for the exciter shaft

housing.

Fill in fresh oil up to the bottom edge of the opening.

Screw in the oil drain plug (1).

Dispose of oil in an environmentally friendly way.

8.8.7 Replacing the air filter

NOTICE!
Danger of engine damage!

–

Do not start the engine after having removed

the air filter.

Protective equipment:

Working clothes

Safety shoes

Protective gloves

Park the machine safely

Chapter 6.5 „Parking the machine

in secured condition“ on page 64

Allow the engine to cool down.

Fig. 88

Fig. 89

Maintenance – Annually

DFP11

Содержание Dynapac DFP11



















































































































Результаты поиска

Содержание Dynapac DFP11

Отзывы:

Fayat Group Dynapac DFP11, Руководство по эксплуатации, Страница: 93 / 114

Результаты поиска

Содержание Dynapac DFP11

Отзывы: