Fayat Group Dynapac DFP11 Скачать руководство пользователя страница 32

Страница: 32 / 114

3.9 Maintenance work

3.9.1 Preliminary remarks

Adhere to the specified operating, maintenance and repair meas-

ures.

The machine must only be serviced by qualified personnel author-

ised by the operating company.

Keep unauthorised persons away from the machine.

Perform maintenance work only with the engine shut down and the

spark plug connector disconnected.

Make sure that the engine cannot be accidentally started during

maintenance work.

3.9.2 Working on the engine

Drain the engine oil at operating temperature – danger of scalding!

Wipe off spilled oil, catch running out oil and dispose of environ-

mentally.

When working on the air filter no dirt should fall into the air duct.

Do not work on the hot exhaust - danger of burning!

Store used filters and other oil contaminated materials in a sepa-

rate, specially marked container and dispose of environmentally.

3.9.3 Cleaning work

Do not perform cleaning work while the motor is running.

Allow the engine to cool down before starting cleaning work.

Do not use gasoline or other easily inflammable substances for

cleaning.

3.9.4 After maintenance work

Reassemble all guards and protections.

Concerning your safety – Maintenance work

DFP11

Содержание Dynapac DFP11



















































































































Результаты поиска

Содержание Dynapac DFP11

Отзывы:

Fayat Group Dynapac DFP11, Руководство по эксплуатации, Страница: 32 / 114

Результаты поиска

Содержание Dynapac DFP11

Отзывы: