Fayat Group Dynapac DFP11 Скачать руководство пользователя страница 110

Страница: 110 / 114

10.1 Final shut-down of machine

If the machine can no longer be used and needs to be finally shut

down you must carry out the following work and have the machine

disassembled by an officially recognized specialist workshop.

DANGER!
Danger to life caused by explosive gas-air

mixes!

–

Do not allow gasoline to come into contact with

hot components.

–

Smoking and open fire is prohibited.

–

Keep gasoline away from heat sources, sparks

and other sources of ignition.

–

Do not spill any gasoline.

–

Components that previously contained gaso-

line must not be cut with a cutting torch.

WARNING!
Health hazard caused by fuels and lubricants!

–

Safety regulations and environmental protec-

tion regulations must be followed when han-

dling fuels and lubricants

Chapter 3.4 „Han-

dling fuels and lubricants“ on page 23

Protective equipment:

Working clothes

Safety shoes

Protective gloves

Safety goggles

Empty the fuel tank.

Drain engine oil from engine and exciter housing.

Disposal – Final shut-down of machine

DFP11

110

Содержание Dynapac DFP11



















































































































Результаты поиска

Содержание Dynapac DFP11

Отзывы:

Fayat Group Dynapac DFP11, Руководство по эксплуатации, Страница: 110 / 114

Результаты поиска

Содержание Dynapac DFP11

Отзывы: