Fayat Group BOMAG BW 213 D-5 Скачать руководство пользователя страница 37

Страница: 37 / 222

3.4.4

Safety regulations and environmental protection regula-
tions for handling hydraulic oil

WARNING!
Danger of injury caused by

escaping pressure fluid!

– Always depressurize the

hydraulic system before starting

work in the hydraulic system.

– Wear your personal protective

equipment (protective gloves,

protective clothing, goggles).

Should pressure fluid penetrate the

skin, immediate medical help is

required.

WARNING!
Danger of burning by ignited

hydraulic oil!

– Do not allow hydraulic oil to

come into contact with hot com-

ponents.

– Smoking and open fire is pro-

hibited!

– Wear your personal protective

equipment (protective gloves,

protective clothing).

Fig. 6

Concerning your safety – Handling fuels and lubricants

BW 213 D-5

Содержание BOMAG BW 213 D-5































































































































































































































Результаты поиска

Содержание BOMAG BW 213 D-5

Отзывы:

Бренды по названию

Популярные бренды

Fayat Group BOMAG BW 213 D-5, Инструкция по эксплуатации, Инструкция по обслуживанию

Результаты поиска

Содержание BOMAG BW 213 D-5

Отзывы:

Бренды по названию

Популярные бренды