Fayat Group BOMAG BW 213 D-5 Скачать руководство пользователя страница 27

Страница: 27 / 222

3.2

Definition of responsible persons

3.2.1

Operating company

The operating company is the natural or jurid-

ical person who uses the machine or in who's

name the machine is used.
The operating company must make sure that

the machine is only used for the purpose it is

intended for and in strict compliance with the

safety regulations mentioned in these operating

and maintenance instructions.
The operating company must determine and

assess the danger in his company. It must then

take appropriate action to ensure health and

safety at work for his employees and point out

any remaining dangers.
The operating company must determine

whether there are special operation hazards

such as a toxic atmosphere or limiting soil con-

ditions. Such conditions requires special, addi-

tional measures to remove or reduce the

hazard.
The operating company must make sure that

all users read and understand the information

concerning safety.
The operating company is responsible for the

planning and professional execution of regular

safety inspections.

3.2.2

Expert / qualified person

An expert / qualified person is a person who,

based on his/her professional education and

experience, has profound knowledge in the

field of construction equipment and the

machine in question in particular.

Concerning your safety – Definition of responsible persons

BW 213 D-5

Содержание BOMAG BW 213 D-5































































































































































































































Результаты поиска

Содержание BOMAG BW 213 D-5

Отзывы:

Бренды по названию

Популярные бренды

Fayat Group BOMAG BW 213 D-5, Инструкция по эксплуатации, Инструкция по обслуживанию

Результаты поиска

Содержание BOMAG BW 213 D-5

Отзывы:

Бренды по названию

Популярные бренды