Fayat Group Bomag BVT 65 Скачать руководство пользователя

Страница: 93 / 97

10.1 Final shut-down of machine

If the machine can no longer be used and needs to be finally shut

down you must carry out the following work and have the machine

disassembled by an officially recognized specialist workshop.

DANGER!
Danger to life caused by explosive gas-air mixes!

–

Do not allow gasoline to come into contact with hot

components.

–

Smoking and open fire is prohibited.

–

Keep gasoline away from heat sources, sparks

and other sources of ignition.

–

Do not spill any gasoline.

–

Components that previously contained gasoline

must not be cut with a cutting torch.

WARNING!
Health hazard caused by fuels and lubricants!

–

Safety regulations and environmental protection

regulations when handling fuels and lubricants

must be followed

Chapter 3.4 ‘Handling fuels

and lubricants’ on page 23

Protective equipment:

Working clothes

Safety shoes

Protective gloves

Safety goggles

Empty the fuel tank.

Drain oil from engine and tamper foot.

Disposal – Final shut-down of machine

BVT 65

Go to

Discount-Equipment.com

order your parts

Содержание Bomag BVT 65


































































































Результаты поиска

Содержание Bomag BVT 65

Отзывы:

Похожие инструкции для Bomag BVT 65

Бренды по названию

Популярные бренды

Fayat Group Bomag BVT 65, Инструкция по эксплуатации, Инструкция по обслуживанию

Результаты поиска

Содержание Bomag BVT 65

Отзывы:

Похожие инструкции для Bomag BVT 65

Бренды по названию

Популярные бренды