manualshive.com logo in svg

Fayat Group Bomag BVT 65, Инструкция по эксплуатации, Инструкция по обслуживанию, Страница: 73 / 97

Поделиться
Скачать
Fayat Group Bomag BVT 65 Скачать руководство пользователя страница 73

8.7.2  Replacing the fuel filter

Protective equipment:

n

Working clothes

n

Protective gloves

1.

Park the machine in secured condition

 

Ä

 Chapter 6.4 ‘Park

the machine in secured condition.’ on page 55

.

2.

Set the engine stop switch to position "OFF".

ð

The fuel valve is closed.

3.

Disassemble the left engine guard.

4.

NOTICE!
Danger of engine damage!

–

Ensure that no dirt falls into the air intake

channel.

Unscrew the fastening screws (1) from the air filter cover.

5.

Loosen the hose clamps (5) and pull the fuel hoses off the

fuel filter (4).

6.

Loosen the screw (2) to be able to loosen the clamp (3).

7.

Remove the fuel filter from the clamp and collect running out

fuel.

8.

Install the new fuel filter and observe the flow direction

(arrow).

9.

Tighten the screw (2), tightening torque: 8 Nm (5.9 ft

·

lbf).

10.

Fasten the fuel hoses to the fuel filter with hose clamps.

3

Screw M6x8

4

Screw M6x16 with washer

Fig.  60

Fig.  61

Fig.  62

Maintenance – Annually

 

BVT 65

 

77

Go to

Discount-Equipment.com 

to

order your parts

Содержание Bomag BVT 65


































































































Отзывы:

Нет отзывов