Fayat Group Bomag BVT 65 Скачать руководство пользователя страница 66

Страница: 66 / 97

8.6 Monthly

8.6.1 Changing the engine oil

NOTICE!
Danger of engine damage!

–

Change the oil only with the engine at operating

temperature.

–

Use only oil of the permitted specification

Chapter 8.2.1 ‘Engine oil’ on page 65

–

Filling quantity:

Chapter 8.3 ‘List of fuels and

lubricants’ on page 67

Protective equipment:

Working clothes

Protective gloves

Park the machine in secured condition

Chapter 6.4 ‘Park

the machine in secured condition.’ on page 55

Park the machine so that the tamper foot is in horizontal posi-

tion.

WARNING!
Danger of burning on hot components!

–

Wear your personal protective equipment

(protective gloves, protective clothing).

Clean the area around oil dipstick (1) and drain plug (3).

Unscrew the oil dipstick.

Unscrew the drain plug and catch any oil running out.

Clean the oil drain plug and screw it back in with a new seal

ring (2).

Fill in fresh oil up to the bottom edge of the filler bore.

Push the oil dipstick (1) back in.

Check for leaks after a short test run.

10.

Check the oil level on the dipstick, correct if necessary.

11.

Dispose of oil environmentally.

Fig. 44

Fig. 45

Maintenance – Monthly

BVT 65

Go to

Discount-Equipment.com

order your parts

Содержание Bomag BVT 65


































































































Результаты поиска

Содержание Bomag BVT 65

Отзывы:

Fayat Group Bomag BVT 65, Инструкция по эксплуатации, Инструкция по обслуживанию, Страница: 66 / 97

Результаты поиска

Содержание Bomag BVT 65

Отзывы: