Fayat Group 897 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 590

Fayat Group 897 Скачать руководство пользователя страница 65

B 37

7.4

Continuous sound pressure SD2500WS

m

The operator always must use ear protection. The emission value at the ear of the
driver varies depending on the materials used for paving and may even rise above
85 dB(A). If no ear protection devices are used, hearing can be impaired.
The sound emission level of the paver finisher was measured under free-field condi-
tions according to EN 500-6:2006 and ISO 4872.

Sound pressure level at the operator’s position

(at the height of the head):

L

AF

= 85.7

dB(A)

Sound capacity level:

L

WA

= 106.1

dB(A)

Sound pressure level at the vehicle

7.5

Operating conditions during measurement

The diesel engine was running at maximum speed. The screed was lowered into
working position. The tamper and the vibrator were running at min. 50% of their max-
imum speed, the augers at min. 40% and the conveyors at min. 10% of their maxi-
mum speed.

7.6

Measuring point configuration

Hemispherical measuring surface with a radius of 16 m. The machine was at the cen-
tre. The measuring points had been assigned the following coordinates:

Measuring point

2

4

6

8

10

12

Sound pressure level L

AFeq

(dB(A))

73.8

74.5

73.5

72.6

70.6

71.7

Measuring points 2, 4, 6, 8

Measuring points 10, 12

Co-ordinates

X

Y

Z

X

Y

Z

±11.2

±11.2

1.5

- 4.32
+4.32

+10.4

-10.4

11.36
11.36

«
...
63
64
65
66
67
...
»

Содержание 897















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов