manualshive.com logo in svg

Fayat Group 897, Руководство по эксплуатации и техническому обслуживанию, Страница: 309 / 590

Поделиться
Скачать
Fayat Group 897 Скачать руководство пользователя страница 309

D 43 3

Before starting work

(in the morning or when starting paving)

- Heed the safety instructions. 
- Check the personal protective equipment . 
- Take an inspection walk around the paver finisher and check for leaks and damages. 
- Install parts removed for transportation or for the night. 
- When screed is operated with the optional gas heating system, open the closing

valves and the main shut-off valve.

- Perform the check according to the following "Checklist for the machine operator".

Check list for the machine operator

Check!

How?

Emergency stop button 
- on the operating panel 
- on both remote controls

Push in the button. 
The diesel engine and all running drives 
must stop immediately.

Steering

The paver finisher must immediately 
follow every steering wheel movement 
in a precise manner. Check straight 
ahead travel. 

Horn 
- On the operating panel
- on both remote controls 

Briefly press the horn button. 
Horn signal must sound. 

Lights

Switch on with the ignition key, walk 
around the paver finisher to check and 
switch off again. 

Screed hazard flasher 
(with vario screeds)

With the ignition switched on, press the 
switches for extending/retracting the 
screed parts. 
Hazard warning flashers must flash. 

Gas heater system (

o

): 

- Bottle holders 
- Bottle valves 
- Pressure reducer 
- Hose break safety devices 
- Shut-off valves 
- Main shut-off valve
- Connections 
- Indicator lamps of the switch box 

Check:
- Secure seat
- Cleanliness and tightness
- Working pressure 1.5 bar
- Function
- Function
- Function
- Tightness
- All indicator lamps must light up when 

the system is switched on

Содержание 897















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов