background image

Technical Specifications 

 

VIM301 

V I M 3 0 1   U s e r   M a n u a l

 

10 

© 2 0 1 5   F a s t w e l     v . 0 0 2

 

Technical Specifications 

2.1 

General 

 

Video processor: L (SM722G8): 

 

32-bit VGA core; 

 

128-bit Drawing Engine (100 MHz); 

 

PCI 2.1 compatible controller, 33 MHz, Master/Slave modes; 

 

200 MHz RAMDAC; 

 

Simultaneous operation with three displays; 

 

Video memory: 8 MB, 64-bit, 100 MHz, integrated in processor;  

 

Video BIOS:  

 

Soldered 64 KB BIOS chip; 

 

ACPI 1.0 compatible; 

 

Interface connectors: 

 

PCI/104 (PCI); 

 

PC/104 (ISA); 

 

One RGB interface; 

 

Up to two LVDS interfaces; 

 

Up to two Flat Panel (FP) interfaces; 

 

One SGD 4-bit LCD interface for Planar EL panel; 

 

Up to four video input channels; 

 

Support for LCD 

panels with resolutions 640×480, 800×600, 1024×768, 1280×1024 

and 9, 12, 18, 24-bit color; 

 

TFT/DSTN LCD support; 

 

Support for Planar monochrome EL displays with resolution 320×240; 

 

Software compatibility: 

 

MS DOS

® 6.22, FDOS 6.22, QNX 6.3, Windows 98, Me, NT, 2K, XP, CE 4.2, 

and Linux 2.6 operating systems. 

Содержание VIM301























































Отзывы: