Fast 9553P страница 39 Скачать руководство пользователя

Страница: 39 / 87

SPECIFICATIONS

SPECIFICATIONS

3PT Sprayer 9553P / 9573P

Page 39

SPECIFICATIONS

Tractor Power, Size Recommendation

Use the machine with a tractor providing drawbar power in the following ranges:

Model

Tank Size, L (gal.)

Tractor Power, kW

(HP)

Quick Hitch

Compatibility

9553P

1893 (500)

97 (130)

Cat. 3, 4, 4N

95739

2839 (750)

IMPORTANT: Verify the main tank is empty before transporting on road.

Hydraulic System Requirements

A tractor hydraulic system with ISO hydraulic couplers is required.

Tractor Selective Control Valves (SCV) at the listed flowrates and pressure are required for
following:

Circuit SCV Function

Flowrate

Pressure

Wing Fold Valve Block

15.1 LPM (4 GPM)

20684 kPa (20.7 bar) (3000 PSI)

Chemical/Fertilizer
Pump Drive Motor

49.2 LPM (13 GPM) 17237 kPa (172.4 bar) (2500 PSI)

Machine Dimensions & Specifications

Boom

60’

66’

80’

88’

90’

100’

Transport Height

3.2 m (10 ft. 5 in.)

3.4 m (11 ft. 1 in.)

Transport Width

3.8 m (12 ft. 6 in.)

Field Width

18.3 m

(60 ft.)

20.1 m

(66 ft.)

24.4 m

(80 ft.)

26.8 m

(88 ft.)

27.4 m

(90 ft.)

30.5 m

(100 ft.)

Weight, empty
(approximate)

2268 kg

(5000

lbs.)

2336 kg

(5150

lbs.)

2495 kg

(5500

lbs.)

2585 kg

(5700

lbs.)

2631 kg

(5800

lbs.)

2744 kg

(6050

lbs.)

Section Count

3 or 5

4, 6, or 8

5, 6, or 8

6 or 8

Nozzles

Single or Triple Bodies

Quick-Fill Size

51 mm (2 in.)

Standard
Hydraulic Pump

ACE FMCSC-205F-HYD-304

Controller Power

12 VDC, 15 A

Cab Fold Box

12 VDC, 10 A

Содержание 9553P
























































































Результаты поиска

Содержание 9553P

Отзывы:

Похожие инструкции для 9553P

Бренды по названию

Популярные бренды

Fast 9553P, Руководство пользователя

Результаты поиска

Содержание 9553P

Отзывы:

Похожие инструкции для 9553P

Бренды по названию

Популярные бренды