Farm King Model 1050 Скачать руководство пользователя страница 23

Страница: 23 / 174

Safety - 10" Backsaver Auger

SAFETY SIGN-OFF FORM

Farm King follows the general Safety Standards specified by the American Society of Agricultural and Biological

Engineers (ASABE) and the Occupational Safety and Health Administration (OSHA). Anyone who will be operating

and / or maintaining the Backsaver Auger must read and clearly understand ALL Safety, Operating and Maintenance

information presented in this manual.
Annually review this information before the season start-up and make these periodic reviews of SAFETY and

OPERATION a standard practice for all of your equipment. An untrained operator is unqualified to operate this

machine.
The following sign-off sheet is provided for your record and to show that all personnel who will be working with

the equipment have read and understand the information in this Operator and Parts Manual and have been

instructed in the operation of the equipment.

SIGN-OFF SHEET

Date

Employee’s Signature

Employer’s Signature

Instructions are necessary before operating or servicing equipment. Read and understand the Operator

And Parts Manual and safety signs (decals) on equipment. Follow warnings and instructions in the

manuals when making repairs, adjustments or servicing. Check for correct function after adjustments,

repairs or service. Untrained operators and failure to follow instructions can cause injury or death.

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды