Farm King Model 1050 Скачать руководство пользователя страница 169

Страница: 169 / 174

169

Warranty - 10" Backsaver Auger

WARRANTY

Limited Warranty

BASE LIMITED WARRANTY
Farm King provides this warranty only to original retail purchasers of its products. Farm King warrants to such

purchasers that all Farm King manufactured parts and components used and serviced as provided for in the

Operator’s Manual shall be free from defects in materials and workmanship for a period following delivery to the

original retail purchaser of two (2) years. This limited warranty applies only to those parts and components

manufactured by Farm King. Parts and components manufactured by others are subject to their manufacturer’s

warranties, if any.

Farm King will fulfill this limited warranty by, at its option, repairing or replacing any covered part that is

defective or is the result of improper workmanship, provided that the part is returned to Farm King within thirty

(30) days of the date that such defect or improper workmanship is, or should have been, discovered. Parts must

be returned through the selling Farm King Dealer and the buyer must prepay transportation charges.

Farm King will not be responsible for repairs or replacements that are necessitated, in whole or part, by the use

of parts not manufactured by or obtained from Farm King. Under no circumstances are component parts

warranted against normal wear and tear. There is no warranty on product pump seals, product pump bearings,

rubber product hoses, pressure gauges, or other components that require replacement as part of normal

maintenance.

REPAIR PARTS LIMITED WARRANTY
Farm King warrants genuine Farm King replacement parts purchased after the expiration of the Farm King Limited

Warranty, and used and serviced as provided for in the Operator’s Manual, to be free from defects in materials or

workmanship for a period of thirty (30) days from the invoice date for the parts. Farm King will fulfill this limited

warranty by, at its option, repairing or replacing any covered part that is defective or is the result of improper

workmanship, provided that the part is returned to Farm King within thirty (30) days of the date that such defect

or improper workmanship is, or should have been, discovered. Such parts must be shipped to the Farm King

factory at the purchaser’s expense.

WHAT IS NOT COVERED
Under no circumstances does this limited warranty cover any components or parts that have been subject to the

following: negligence; alteration or modification not approved by Farm King; misuse; improper storage; lack of

reasonable and proper maintenance, service, or repair; normal wear; damage from failure to follow operating

instructions; accident; and/or repairs that have been made with parts other than those manufactured, supplied,

and or authorized by Farm King.

AUTHORIZED DEALER AND LABOR COSTS
Repairs eligible for labor under this limited warranty must be made by Farm King or an authorized Farm King

dealer. Farm King retains the exclusive discretion to determine whether it will pay labor costs for warranty

repairs or replacements, and the amount of such costs that it will pay and the time in which the repairs will be

made. If Farm King determines that it will pay labor costs for warranty work, it will do so by issuing a credit to

the dealer’s or distributor’s account. Farm King will not approve or pay invoices sent for repairs that Farm King

has not previously approved. Warranty service does not extend the original term of this limited warranty.

Payment of labor costs will only be considered on repairs made to manufactured parts and components that have

been found defective during a period of one (1) year following delivery to the original retail purchaser.

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды